Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
Just how do you really feel in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bathtub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a reasonably tough project. If the old bathtub is conveniently obtainable, the job can move immediately; if you need to open a wall surface to eliminate the old tub and also place the new bath tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will require an assistant to move out the old bathtub and embeded in the new one. Make certain you have qualified on your own for the task and also are comfortable trying it. Rather than employing a contractor to take control of a halfway-completed job, it is better to think about employing one prior to you start. Possibilities are you may need an expert plumber to make tube connections.
This article will assist you set up a new bath tub in your bathroom if you have currently bought a new bathtub as well as do not require to transform the plan of your previous supply of water pipes.
Your tools and also material checklist ought to comprise the following:
Planning for the Installation
To start with, the supporting frame provided with the bath must be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps system to stop strain on the bath tub.
Fit the versatile faucet adapters to the bottom of the two taps using 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final position.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the water system. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of removing the existing faucets can be quite problematic due to the restricted access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a towel ready for the continuing to be water that will certainly originate from the pipelines. Once the supply pipelines have actually been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning during this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
Before carrying on to fit the new taps, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Bath tub
Making use of the two wood boards under its feet, position the bath tub in the required placement. The wooden boards are valuable in evenly spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bath tub until the level checks out degree.
To install taps, fit all-time low of the furthest versatile faucet port to the suitable supply pipe by making a compression join; then do the very same for the various other tap.
Activate the water supply as well as inspect all joints and brand-new pipework for leakages and also tighten them if necessary. Fill the tub and additionally inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
Finally, fix the bath paneling as described in the producer's user's manual. Tiling and also securing around the bath tub ought to wait until the bath tub has been used a minimum of once as this will settle it right into its last placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will require a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin ensuring that the washers are in area in between the tap and the sink. Secure the faucet in place with the manufacturer given backnut. When the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind should be connected to the tap ends first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, resulting in complications with dampness as well as feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and also cartridges, as well as are capable of securing voids up to a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill the tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can break relatively very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the marketplace. It is recommended to fit the tiles using waterproof or water resistant sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm very focused on How to Install a Bathtub Yourself and I am hoping you enjoyed reading our blog posting. So long as you enjoyed reading our page please don't forget to share it. Kudos for your time. Kindly stop by our blog back soon.
Quality assured, call! Report this page